How To Remove A Lazy Susan Shelf

Download Commodity

Download Article

Adjusting misaligned Lazy Susan units might seem intimidating, but the near common corrections you'll need to brand tin can be done at abode using standard tools. Fix rotation problems by adjusting the center shaft or lesser shelf position. Remedy misaligned doors by correcting the door position from inside the overall unit.

1. i

   Pinpoint where rotation issues are occurring. When a Lazy Susan becomes stiff and difficult to rotate, the problem is usually acquired past either the center shaft or the position of its bottom shelf. Lightly spin the Susan and notation where it locks up, has difficulty turning, or has poor clearance.^[1]

   • If the center movable shelf begins to bind, it volition foreclose gratuitous rotation. In this situation, you lot'll need to loosen this shelf.
   • If the round shelves slip down the center shaft, the bottom shelf can begin to drag, making it difficult to plow. You will demand to adjust the height of this shelf to gear up the problem.

2. ii

   Locate the locking bolt to conform the center shaft. Look at the top of the heart shaft. There should exist one large commodities locking the exterior shaft to a metal sleeve positioned inside the shaft. This is the locking commodities for the shaft.^[2]

   • This bolt holds the middle shaft in place and maintains the length of the shaft. Sometimes excess pressure level from this commodities can cause the shaft to bind.
   • On some models, the locking bolt might exist located at the bottom of the Susan, however, in most cases, it will found most the top.

   Advertizing

3. 3

   Loosen the bolt. If annihilation is inside your Lazy Susan, empty it and then you lot take more space to work. Using a wrench or ratchet, loosen the commodities by turning it i-quarter of a total rotation counterclockwise. At offset, the commodities may require some elbow grease to suspension loose.

   • Only loosen the bolt enough to manipulate the hardware within the eye shaft. On some models, this might require more or less than one-quarter rotation.
   • Mostly, it's better to loosen the bolt in small increments. This will prevent y'all from loosening it also much, which could event in the alignment of the Susan being thrown off.

4. 4

   Move the adjusting rod. At present that the commodities is loose, you'll be able to adjust the centre shaft. Slide the metal adjusting sleeve the bolt was holding in identify no more than 1 inch (2.5 cm) to provide better clearance between the heart shaft and top of the cabinet.^[iii]

   • Work in small increments when adjusting the heart shaft. Large adjustments could cause the Lazy Susan to topple over.

5. 5

   Tighten the commodities to cease adjusting the centre shaft. Use your wrench or ratchet to advisedly refasten the locking commodities in place. Practise not over-tighten the bolt. Information technology should be looser than it was initially, but still tight enough to agree the adjusting rod in place.^[iv]

6. 6

   Locate the locking screws to conform the shelf position. Well-nigh Lazy Susans should have two or more locking screws located at the center of each shelf. These screws concur the shelves to the eye shaft.

   • When all of the shelves are held together past the front end decorative panel, you will need to adapt the entire shelf system. In this case, there may non be screws located at the tiptop of each shelf.
   • If the shelves must be adjusted separately, you'll only need to work with the bottom shelf. Locate the locking screws in the bottom shelf merely.

7. vii

   Loosen the screws. Loosen the locking screws using a Phillips-caput screwdriver or like tool. Concur the screwdriver and then its head meets the fastener straight on. Apply firm pressure down on the spiral while turning counterclockwise to forestall stripping fastener hardware.^[5]

   • Screws tin be left in their holes once they have been unattached from the center shaft. Nonetheless, you may desire to gear up loosened screws off to the side to prevent whatsoever from getting lost.

8. 8

   Raise the shelves to finish adjusting shelf position. Advisedly elevator the lesser shelf or entire shelf arrangement until there is roughly half an inch (ane.25 cm) of space between the bottom shelf and the lesser of the cabinet.

   • The shelves may resist this adjustment and brainstorm bounden on the center shaft. Maneuver shelves until they are level and at a suitable height.
   • Under no circumstances should you lubricate the center shaft. Doing and so could foreclose the screws from belongings their position.

9. 9

   Tighten the screws. Hold the shelf in place with one mitt and utilize your free hand to tighten the locking screws dorsum in identify with a screwdriver. Accept care not to permit the shelf slip as yous reattach fasteners, as this could cause information technology to become uneven or binding.^[6]

   • Brand the screws every bit tight as possible without stripping any of the hardware. The shelves must be stationary and secure to foreclose this kind of misalignment.

Advertizement

1. i

   Locate where at that place are door issues. Door problems are unremarkably easier to identify than rotation problems. The door of the unit may close unevenly or it may non have sufficient clearance at the top, bottom, or sides of the chiffonier.

   • If the door does not close completely, or if it closes unevenly, you'll need to adjust the doors until they are centered correctly inside the frame.
   • When the height or bottom clearance is insufficient, you'll observe the gaps at both sides of the door will be unequal.
   • When the side clearance is insufficient, the door will appear crooked. Additionally, the gaps effectually it will but unequal.

2. 2

   Loosen the collar spiral when doors close unevenly. Open the door and locate the collar at the top of the unit. For many models, this role will exist made of white plastic. Apply a Phillips-head screwdriver to loosen the screw on this collar.

   • Loosen the screw by 1 full counterclockwise rotation. Even loosened, the spiral should remain in its position in the collar.

3. iii

   Rotate the shelf unit and door counterclockwise. Using both hands, advisedly rotate the unabridged shelf unit and door in a counterclockwise direction. Continue until the collar hits the catch latch located at the dorsum of the ceiling bracket.^[7]

   • Plow the Lazy Susan slowly. Listen for a slight click. This is a signal that y'all've reached the catch latch.
   • Once you hit the catch latch, the neckband should exist properly aligned with the spring. You should feel a slight resistance to boosted counterclockwise turning.

4. four

   Rotate the door. Gradually rotate the door in a clockwise direction until information technology reaches the verbal center-front. If possible, accept a step back and check the alignment from a distance. Make certain the door is precisely in place earlier moving on.

   • The plastic collar should remain fixed in place as you rotate the door, so it may be hard to pace away. Have a friend or family member help you evaluate the door position, in these cases.
   • If you lot accidentally rotate past the middle-forepart position, continue rotating the door in a clockwise direction. Practise not rotate it counterclockwise until after you stop setting it.

5. 5

   Turn the entire associates. Carefully and slowly rotate the unabridged associates in a counterclockwise direction. Continue turning the assembly until the collar screw faces you. The door and neckband should maintain their alignment as you plow the assembly.^[8]

   • It may help you to maintain the position of the collar and door by marking their correct positions with a piece of painter'south tape, masking record, or something similar.

6. 6

   Tighten the spiral to finish adjusting uneven doors. Tighten the neckband spiral back into its original position. The door should now be properly aligned and fixed into place. Give the Lazy Susan a few spins to check that everything works correctly, and your door aligning is finished.^[nine]

   • To prevent the collar from twisting out of place while information technology's fastened, you may need to hold it in place as the screw is tightened.

Advertisement

1. 1

   Remove the retainer prune to improve top and bottom clearance. Locate the plastic retainer prune at the bottom of the middle shaft. Firmly grasp the prune between your fingers, open information technology, and pull it out. Under the clip should be a cutting-out portion of the shaft with a thumbscrew adjustment wheel.

   • The cabinet will need to be completely empty when you make this aligning. Practice not attempt to complete the process when the shelves are loaded, particularly if they are heavily loaded.

2. 2

   Plow the adjustment wheel. Utilize your fingers to turn the thumbscrew adjustment bicycle in the cut-out portion of the middle shaft. Rotate the wheel clockwise to raise the door and counterclockwise to lower the door.

   • More often than not you can expect that for each total rotation of the screw the height will be adjusted by about one/32 in (0.8 mm).
   • You may need to apply gentle pressure to the underside of the bottom shelf to aid the adjustment if you are attempting to raise the door.^[10]

3. 3

   Replace the retainer clip to complete the superlative and bottom adjustment. After adjusting the door to the proper height, return the servant clip to its original position at the bottom of the pole. The clip should fasten back into place firmly.^[xi]

   • Information technology's a adept idea to tighten all of the adjustment screws attached to the center shaft, shelves, and door later on setting the peak. Doing this could prevent the door from falling out of alignment over again.

4. 4

   Outline the top and bottom brackets when side clearance is insufficient. Using an erasable pencil, lightly outline the current position of the top and bottom brackets. If lighting is too poor within the cabinet to make these marks hands, use a flashlight or electrical lantern.

   • Doing this will give y'all a reference point to work from as you make the aligning. Pencil marks can be erased once yous complete the process.

5. v

   Realign the pin pole from the top. Utilise a screwdriver to remove the setscrews and loosen the star washers holding the pivot housing in place on both sides of the pin pole. Conform the pivot housing and pin pole until both are centered and aligned.^[12]

   • When the star washers are in identify but before fastening the setscrews, take a stride back and look over your Lazy Susan. If the side clearance is still uneven, remove the washers and readjust the pivot.
   • Use your outline to guide your adjustments. For example, if the left side is low, you'll probable demand to move the pivot pole and housing to the right.

6. 6

   Refasten the pivot housing. Once you tighten the star washers, you'll be set up to return the setscrews to their original position. When the screws are in place, check the side clearance of the Lazy Susan again to brand sure that it wasn't altered as y'all refastened its hardware.^[13]

   • This adjustment may take intendance of your side clearance problem. If the lower one-half of your Susan appears to be misaligned, you'll take to arrange the pivot base of operations in add-on to its meridian.

7. 7

   Realign the pivot base when necessary. Open the door wide enough to expose the bottom subclass on either side of the Susan. Loosen this bracket by removing the fastening setscrew and star washer with a screwdriver. Now you can realign the pivot cam (metallic arm) base so that it's centered.^[14]

   • You'll accept to repeat this process on the opposite side of the Lazy Susan where you'll find an identical bracket/pivot cam base of operations.
   • Work on brackets one at a time. After you've taken apart, realigned, and refastened the first subclass, move on to the side by side 1.
   • When properly centered, the pivot cam bases of both sides should exist aligned with regard to the center pole.

8. 8

   Refasten the bracket. Exist conscientious when refastening; if you jostle the pivot cam, it could exist knocked out of alignment. Replace the star washers and reattach the setscrews for the bracket. When fastened, similarly adapt the reverse side bottom bracket/pin cam base.

   • Verify that the position did non become altered while you were returning these pieces to their original positions by stepping dorsum and evaluating the evenness of the side clearance.

9. 9

   Check the door to complete your side clearance adjustment. Sometimes these alignments (especially those made to pivots) can require several attempts before they are resolved. Double check door alignment after completing the top and bottom adjustments, especially.^[15]

   • If the side clearance is however unequal, you volition demand to readjust the top pivot pole and/or bottom pivot cams.

Advertisement

Add New Question

• Question

  How do I tighten a Lazy Susan that keeps turning around and effectually? It won't lock in place.

  

  In that location is a plastic clasp at the top of the Lazy Susan. You will run into a notch in it that should grab so that information technology holds the unit in place. Commonly, the older units will bear witness the plastic to be worn. Simply replace the plastic piece, and it should realign and close properly.

• Question

  What shelf do I put the heavy items on, top or bottom?

  

  Putting the heavy items like canned goods on superlative will increase the chances of the shelf breaking, then put heavy stuff non the bottom instead. The top shelf is improve for boxes of pasta and numberless of rice.

• Question

  How do I prepare set screws that won't tighten?

  

  If the screws for your Lazy Susan don't tighten, the fasteners or the attaching hardware may exist stripped. This means that damage has been done to the part of the hardware intended to grip the fastener (like the grooves of a screw). Supplant stripped hardware and attempt over again.

• Question

  How can I adjust a bottom corner chiffonier lazy susan that has the cabinet door attached?

  

  If y'all have the one with a cam at the elevation of the center pole and a screw with a spring, then adjusting the screw on the side that has a spring on it will adjust how the outer surface of the lazy susan "door" aligns with the rest of the cabinets. Don't be afraid to tighten all the style or loosen as far every bit possible. From what I tin tell, the screw will non come out. I turned the screw in and thought I counted the turns. Then backed it out again the aforementioned amount of turns and all of a sudden the door was more than an inch out of alignment. I had to back it out a lot further to reset the alignment.

• Question

  How do I fix a lazy Susan if the shelf adjuster brutal and took the shelf with it? At that place is not enough room to suit it and the flange is crooked.

  

  If the shelf arrange fell and knocked a shelf out, damaging the shelf flange, you lot may need to completely disassemble the shelf, replace the damaged hardware (inexpensive flanges tin be bought at most hardware stores), and then reinstall the Lazy Susan.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Cheers for submitting a tip for review!

Things Y'all'll Demand

• Eraser
• Flashlight (or electric lantern for calorie-free; optional)
• Pencil
• Phillips-caput screwdriver
• Standard screwdriver
• Wrench (or ratchet set up)

Near This Commodity

Article Summary X

If you're having issues with your Lazy Susan, you should be able to arrange it using standard tools. Before yous make whatsoever adjustments, empty the cupboard and then yous have space to work. If the shelves are stiff when yous turn them, loosen the locking commodities at the top of the middle shaft with a wrench or ratchet, and so movement the adjusting rod an inch, and tighten the bolt. To fix the shelf meridian, unscrew the locking screws on the central shaft that hold each shelf, adjust the pinnacle, then tighten the screws once more. If the doors are misaligned, utilise a Philips-head screwdriver to loosen the spiral at the top of the doors, rotate the shelf unit and door counterclockwise until the peak hits the latch, then rotate the door clockwise until it reaches the center. For more tips, including how to adjust the clearance within your Lazy Susan, read on!

Did this summary help you lot?

Thanks to all authors for creating a page that has been read 174,924 times.

Did this article assistance you?

Source: https://www.wikihow.com/Adjust-a-Lazy-Susan

Share this post